jQuery Mobile Framework
Search Home >> Standards Wordwide >> Australia Standards(AS) >> AS 3814-2009 industrial and commercial gas-fired appliances

AS 3814-2009 industrial and commercial gas-fired appliances

Standard Number:  AS 3814-2009
Title:  industrial and commercial gas-fired appliances
Language:  English
Publication Date:  2009/8/12
Status:  Current
Publisher:  Australia Standards(AS)
Price:  
Number of Pages:112  

Description:Specifies the uniform minimum requirements for the design, construction and safe operation of Type B appliances that are intended for use with town gas, natural gas, simulated natural gas, liquefied petroleum gas and tempered liquefied petroleum gas or any combination of these gases either together or with other fuels.  
Catalog:Document Contents
AS 3814-2009 INDUSTRIAL AND COMMERCIAL GAS-FIRED APPLIANCES
PREFACE
CONTENTS
SECTION 1 SCOPE, APPLICATION AND DEFINITIONS
1.1 SCOPE
1.1.1 General
1.1.2 Exclusions from Standard
1.2 APPLICATION
1.2.1 General
1.2.2 Appliance installation
1.2.3 New materials and methods
1.2.4 Unusual installations
1.2.5 Modification or relocation of an appliance
1.3 REFERENCED DOCUMENTS
1.4 DEFINITIONS
1.4.1 Accessible
1.4.2 Air curtain
1.4.3 Air-gas mixing machine
1.4.4 Appliance
1.4.4.1 Type A appliance
1.4.4.2 Type B appliance
1.4.5 Approved
1.4.6 Atmospheric burner
1.4.7 Authorized installer
1.4.8 Auto-ignition temperature (AIT)
1.4.9 Automatic burner
1.4.10 Automatic ignition
1.4.11 Bleed line
1.4.12 Burner
1.4.12.1 Atmospheric burner
1.4.12.2 Automatic burner
1.4.12.3 Forced draught burner
1.4.12.4 Induced draught burner
1.4.12.5 Multi-fuel alternative burner
1.4.12.6 Multi-fuel burner
1.4.12.7 Multi-fuel simultaneous burner
1.4.12.8 Part automatic burner
1.4.13 Burner off cycle
1.4.14 Burner unit
1.4.15 Certified/Certification
1.4.16 Certifying body
1.4.17 Combination gas control
1.4.18 Combustion products
1.4.19 Common flue
1.4.20 Critical time
1.4.21 Cross lighting
1.4.22 Damper
1.4.23 Direct-fired air heater
1.4.24 Direct-fired oven
1.4.25 Double block and vent
1.4.26 Draught diverter
1.4.27 Electronic flame safeguard
1.4.28 Excess air
1.4.29 Fail-safe
1.4.30 Flame abnormality
1.4.31 Flame detector
1.4.32 Flame establishment period
1.4.33 Flame failure response time
1.4.34 Flame lift
1.4.35 Flame proving period
1.4.36 Flame safeguard
1.4.37 Flame safeguard system
1.4.38 Flue
1.4.38.1 Common flue
1.4.38.2 Natural draught flue
1.4.38.3 Open flue
1.4.38.4 Secondary flue
1.4.38.5 Slip joint
1.4.39 Flue gases
1.4.40 Flue system
1.4.41 Flue terminal
1.4.42 Flued appliance
1.4.43 Flueless appliance
1.4.44 Forced draught burner
1.4.45 Forced or induced draught combustion system
1.4.46 Gas
1.4.46.1 Natural gas (NG)
1.4.46.2 Simulated natural gas (SNG)
1.4.46.3 Town gas (TG)
1.4.46.4 Tempered liquefied petroleum gas (TLP)
1.4.46.5 Liquefied petroleum gas (LP gas)
1.4.47 Gas/air ratio control
1.4.48 Gas consumption
1.4.49 Gasfitting work
1.4.50 Gas pressure regulator
1.4.51 Gas tight
1.4.52 Hazardous conditions
1.4.53 High gas pressure detector
1.4.54 Hose
1.4.55 Hose assembly
1.4.56 Hot water boiler
1.4.57 Ignition temperature
1.4.58 In service
1.4.59 Indoor flueless appliance
1.4.60 Induced draught burner
1.4.61 Injector
1.4.62 Interlock
1.4.63 Intermittent pilot
1.4.64 Interrupted pilot
1.4.65 Leakage detection system
1.4.66 Light back
1.4.67 Limit device
1.4.68 Lockout
1.4.69 Lower explosive limit (LEL)
1.4.70 Low-gas-pressure detector
1.4.71 Manual ignition
1.4.72 Mixing blower
1.4.73 Mixing tube
1.4.74 Modification
1.4.75 Multi-fuel alternative burner
1.4.76 Multi-fuel burner
1.4.77 Multi-fuel simultaneous burner
1.4.78 Natural draught
1.4.79 Natural draught burner
1.4.80 Natural draught flue
1.4.81 No-flow
1.4.82 Nominal gas consumption
1.4.83 Non-return valve
1.4.84 Open flued appliance
1.4.85 Operating pressure
1.4.86 Over-pressure protection system
1.4.87 Over-temperature cut-out device
1.4.88 Over-temperature limiting device
1.4.89 Part automatic burner
1.4.90 Permanent pilot
1.4.91 Pilot
1.4.92 Position indicator switch
1.4.93 Closed position indicator switch
1.4.94 Open position indicator switch
1.4.95 Position-proving system
1.4.96 Process after-burner
1.4.97 Programmable electronic system (PES)
1.4.98 Programming flame safeguard
1.4.99 Proof-of-closure switch
1.4.100 Protected pilot
1.4.101 Purge (or purging)
1.4.102 Purge volume
1.4.103 Rated working pressure
1.4.104 Regulator
1.4.105 Relief device
1.4.106 Safe start check
1.4.107 Safety shutdown
1.4.108 Safety shut off system
1.4.109 Safety shut off system, double block and vent
1.4.110 Safety shut off valve
1.4.111 Set pressure
1.4.112 Start gas
1.4.113 Steam boiler
1.4.114 Stoichiometric combustion
1.4.115 Supervised burner
1.4.116 Supervised pilot
1.4.117 Technical regulator
1.4.118 Temperature limit device
1.4.119 Test firing valve
1.4.120 Thermostat
1.4.121 Valve
1.4.122 Valve train
1.4.123 Vent line
1.4.124 Vent valve, double block and vent safety shut off system
1.4.125 Water heater
SECTION 2 REQUIREMENTS FOR DESIGN AND CONSTRUCTION
2.1 GENERAL REQUIREMENTS
2.1.1 Appliance design
2.1.2 Suitability for location
2.1.3 Controls and indicating devices
2.1.4 Design of adjustable devices
2.1.5 Appliance to be well constructed
2.1.6 Appliance parts to be secure against accidental displacement
2.1.7 Appliance parts to be secure for satisfactory operation
2.1.8 Appliance to be free of sharp edges
2.1.9 Appliance supports to be of adequate strength
2.1.10 Provision to be made for sampling flue gases
2.2 CONTROLS, BURNER AND SAFETY DEVICE ACCESS
2.3 FLAME VISIBILITY
2.3.1 Flame to be visible to maintenance personnel
2.3.2 Visual indication of flame to operator
2.4 TEMPERATURES OF SURFACES AND COMPONENTS
2.5 RESTRICTION ON ELECTRICAL CONNECTIONS
2.5.1 Ease of connection
2.5.2 Limit on cross-connection
2.6 ACCESSIBILITY OF MANUAL CONTROLS
2.7 MATERIALS
2.7.1 Materials to be adequate for their intended application
2.7.2 Restriction on use of zinc-base die-castings
2.7.3 Materials to be suitable for gas
2.8 GAS PIPEWORK AND VALVE TRAINS
2.8.1 Gas pipework and valve trains
2.8.2 Enclosure for a valve train
2.8.3 Pressure rating of valve train components
2.8.3.1 Upstream of and including appliance gas pressure regulator
2.8.3.2 Downstream of appliance gas pressure regulator
2.8.4 Requirements where pressurized air, oxygen or a standby gas is to be used
2.8.5 Multi-position manual control valves
2.8.6 Design of valve handles, dials and pointers
2.8.7 Appliance isolating valve
2.8.7.1 Appliance isolating valve to be fitted
2.8.7.2 Requirements for appliance isolating valve
2.8.7.3 Location of appliance isolating valve
2.8.7.4 Identification of appliance isolating valve
2.8.7.5 Connection of appliance isolating valve
2.8.8 Main Burner Isolation
2.8.8.1 Main burner isolation valve
2.8.8.2 Main burner isolation for commissioning
2.8.9 Restriction on test firing valve
2.8.10 Pilot burner isolating valve
2.9 GAS PRESSURE REGULATION
2.9.1 Gas pressure regulator to be fitted
2.9.2 Requirements for a gas pressure regulator
2.9.4 Position of gas pressure regulator
2.9.5 Venting of gas pressure regulator
2.10 GAS OVER-PRESSURE PROTECTION
2.10.1 Requirement where over-pressure protection shuts off the gas supply
2.10.2 Where over-pressure protection system is to be fitted
2.10.3 Setting of over-pressure protection system
2.10.4 Location of over-pressure protection system sensing point
2.11 GAS LOW-PRESSURE PROTECTION
2.11.1 Low-gas-pressure detector to be fitted
2.11.2 Requirements of low-gas-pressure detector
2.12 GAS PRESSURE TEST POINTS
2.12.1 Location of pressure test points
2.12.2 Maximum orifice size of a pressure test point
2.12.3 Sealing of a pressure test point
2.13 GAS FILTER
2.13.1 Filter to be fitted
2.13.2 Requirements and location of filter
2.14 SAFETY SHUT OFF SYSTEMS
2.14.1 Safety shut off valve and vent valve
2.14.2 Function of safety shut off system
2.14.3 Safety shut off valve system requirements for main and start gas supplies
2.14.3.1 General
2.14.3.2 Concession for atmospheric burner not exceeding 500MJ/h
2.14.3.3 Concession for atmospheric burner not exceeding 1GJ/h
2.14.3.4 Concession for forced or induced draught burner up to 200MJ/h
2.14.3.5 Concession for forced or induced draught burner up to 1GJ/h
2.14.3.6 Concession for a main burner up to 1GJ/h igniting at low rate
2.14.3.7 Concession for a burner using a separate start gas line
2.14.3.8 Provision for start gas to be taken from between safety shut off valves for a ma...
2.14.4 Energizing of automatic safety shut off valves
2.14.5 Ignition of main burner by separate pilot
2.14.6 Requirements for a safety shut off valve and vent valve
2.14.6.1 Rated working pressure
2.14.6.2 Orientation
2.14.6.3 Size of vent valve for a double block and vent safety shut off system
2.14.6.4 Size of vent valve for a leakage detection system
2.14.6.5 Arrangement for manual reset vent valve
2.14.7 Safety shut off system not to be bypassed
2.14.8 Vent line requirement
2.14.9 Requirements for a position-proving system
2.14.9.1 Safety shut off valve
2.14.9.2 Vent valve
2.14.9.3 Position-proving system to be interlocked to prevent burner start-up
2.14.9.4 Alarm interlock
2.14.10 Requirements for a leakage detection system
2.14.10.1 Compliance with Standard
2.14.10.2 Leakage detection system to be interlocked to cause lockout
2.14.10.3 Commencement of leakage detection test
2.14.10.4 Alarm interlock
2.14.10.5 Maximum allowable leakage rate
2.14.10.6 Leakage detection system that uses gas at line pressure
2.14.11 Function of interlocks
2.14.12 Requirements of safety shut off system actuators
2.14.12.1 Individual actuators to be fitted
2.14.12.2 Single three-way valve permitted
2.14.12.3 Use of rigidly coupled actuators
2.15 COMBUSTION AIR SUPPLY-GENERAL REQUIREMENTS
2.15.1 Combustion air supply equipment to be correctly sized
2.15.2 Combustion air quality
2.15.3 Air openings to be of adequate size
2.15.4 Air openings not to be obstructed
2.16 COMBUSTION AIR FOR ATMOSPHERIC BURNERS
2.16.1 Primary aeration controls to be corrosion-resistant
2.16.2 Effect of foreign matter on primary aeration controls to be minimal
2.17 FORCED AND INDUCED DRAUGHT BURNERS
2.17.1 Draught characteristics to be specified by burner manufacturer
2.17.2 Proving air flow
2.17.3 Self-check of air flow proving device
2.17.3.1 Self-check to be carried out
2.17.3.2 Failure of air flow proving device during self-check
2.17.4 Safety shutdown to occur if air flow fails
2.17.5 Air-gas mixtures
2.17.5.1 Air-gas mixing machines and mixing blowers
2.17.5.2 Maximum temperature of mixtures
2.18 DAMPERS
2.18.1 Requirements for a fixed or adjustable damper
2.18.2 Requirements for an automatic damper control system
2.18.2.1 Automatic damper to maintain satisfactory combustion
2.18.2.2 Failure of damper mechanism
2.18.2.3 Manual damper control
2.19 APPLIANCE PRE-PURGING
2.19.1 General requirements
2.19.1.1 Function of pre-purge
2.19.1.2 Appliance or process to be pre-purged
2.19.1.3 Pre-purging using an inert medium
2.19.1.4 Supply of inert purging medium to be proved
2.19.2 Pre-purging by mechanical means
2.19.2.1 Mechanical pre-purging required under certain conditions
2.19.2.2 Conduct of mechanical pre-purge
2.19.3 Pre-purging using natural draught
2.19.3.1 Requirements for an appliance using natural draught
2.19.3.2 Pre-purge period using natural draught
2.19.3.3 Pre-purge period included in operating instructions
2.19.3.4 Pre-purge where appliance doors are opened
2.19.4 Pre-purge timer
2.19.5 Pre-purge interlocks
2.19.5.1 Purge flow proving device to be fitted
2.19.5.2 Self-check of purge flow proving device
2.19.5.3 Purging to cease if purge flow fails
2.19.5.4 Pre-purge to reset when purge flow is re-established
2.19.5.5 Proof of operation of zone circulation fans in appliances
2.20 PROCESS CONTROLS
2.20.1 Requirements where appliance safety depends on process
2.20.2 Process limit device to cause lockout
2.20.3 Requirements where appliance safety and operation depend on flow
2.20.4 Provision of over temperature protection on recirculation fans
2.21 IGNITION SYSTEMS
2.21.1 Ignition to be safe, reliable and smooth
2.21.2 Manual ignition systems
2.21.2.1 Requirements for a manually-inserted gas torch
2.21.2.2 Point of ignition to be accessible
2.21.2.3 Explosion relief to be provided for a manually-ignited burner
2.22 PILOT BURNERS
2.22.1 Requirements for a pilot burner with a single main burner
2.22.2 Requirements for supervised pilot burners with multiple main burners
2.22.3 Flames to travel freely to all ports of a multi-port pilot
2.22.4 Bleed lines not to affect ignition of main burner
2.22.5 Protection from blockage
2.23 MAIN BURNERS
2.23.1 Ignition to be in combustion chamber
2.23.2 Main burners subdivided into zones or sections
2.23.3 Requirements for a burner that can be retracted or swivelled
2.23.4 Requirements for cross-ignition
2.23.5 Protection from blockage
2.24 FLAME SAFEGUARD SYSTEMS
2.24.1 Requirements for a flame safeguard system
2.24.2 Flame safeguard system to be fitted
2.24.3 Flame safeguard to comply with classification
2.24.4 Maximum hold-time for a thermoelectric flame safeguard
2.24.5 Maximum shut off time following flame failure
2.24.6 Requirements for a flame detector
2.24.7 Flame simulation to be prevented
2.24.8 Detector not to detect other flame
2.24.9 Requirements for a pilot used on atmospheric burner(s) exceeding 1 GJ/h (275 kW), ...
2.24.10 Detectors to supervise separate flames
2.24.11 Requirements for two flame detectors used with one flame safeguard device or syst...
2.24.12 Detector to ensure cross lighting is complete
2.24.13 Requirements for flame safeguards incorporating hot surface igniters
2.25 BLEED LINES
2.25.1 General requirements for a bleed line termination
2.25.2 Terminating bleed lines in a combustion chamber
2.25.2.1 Combustion chamber to have a supervised burner
2.25.2.2 Bleed line requirements
2.25.2.3 Bleed line termination to be protected against blockage
2.26 APPLIANCE/BURNER CONTROL CIRCUITS
2.26.1 Requirements of control circuits
2.26.2 Gas-actuated controls
2.26.3 Requirements for a programmable electronic system (PES)
2.27 GAS/AIR RATIO CONTROL
2.27.1 General requirements
2.27.2 Interference with interlocks
2.27.3 Variation in control settings and control response
2.27.4 Preheated combustion air control
2.27.5 Requirements for independent gas and air control elements
2.27.6 Special requirements for PES based gas/air ratio control system
2.27.7 Additional requirements for pneumatically controlled gas/air ratio
2.27.8 Gas/air ratio controls incorporating variable speed drive systems
2.27.9 Use of oxygen sensing probes
SECTION 3 OPERATION
3.1 APPLIANCE OPERATION DETAILS
3.2 IGNITION
3.2.1 Starting sequence interlocks before starting burner ignition source
3.2.2 Ignition sequence
3.2.2.1 Commencement of ignition
3.2.2.2 Completion of ignition
3.2.2.3 Start gas flame establishment period
3.2.3 Start gas rate
3.2.3.1 Start gas rate not to exceed determined values
3.3 MAIN BURNERS
3.3.1 Start flame proving period
3.3.2 Main flame establishment period
3.3.3 Main burner supervision
3.3.3.1 Interrupted pilot
3.3.3.2 Intermittent or permanent pilot with a forced or induced draught burner or atmosp...
3.3.4 Main burner to start at reduced rate
3.4 INTERLOCKS AND LIMIT DEVICES
3.4.1 Interlocks and limit devices not to be rendered ineffective
3.4.1.1 Where an interlock is to be fitted
3.4.1.2 Interlock to be tested
3.4.1.3 Requirements for an interlock
3.4.2 Limit devices
3.4.2.1 Limit device to be fitted
3.4.2.2 Limit device not to be an operating control
3.4.2.3 Requirements for a limit device
3.5 OPERATION SEQUENCES
3.5.1 Ignition sequence after power interruption
3.5.2 Programmed sequence for automatic or part automatic burner
3.5.3 Appliance to be left in safe condition
3.5.4 Requirement for lockout on flame failure
3.5.5 Reignition attempt on flame failure
3.5.5.1 Requirements for forced or induced draught burners
3.5.5.2 Requirements for atmospheric burners
3.6 COMBUSTION CONDITIONS
3.6.1 Burners to maintain satisfactory combustion conditions
3.6.2 Leakage of combustion products to be prevented
3.7 COMMISSIONING
3.7.1 Commissioning checks to be carried out
SECTION 4 MARKINGS AND INSTRUCTIONS
4.1 MARKINGS
4.1.1 Markings to be displayed
4.1.2 Marking of controls, dials and gauges
4.1.3 Controls with non-standard operation
4.2 INSTRUCTIONS
4.2.1 Written instructions to be provided
4.2.2 Instructions for operation
4.2.3 Limits of safe operation to be specified
SECTION 5 SPECIAL APPLICATION REQUIREMENTS
5.1 GENE
5.2 HIGH INPUT GAS-FIRED APPLIANCES
5.2.1 General
5.2.2 Start-up where multiple main burners are fitted
5.2.3 Manual ignition where multiple main burners are fitted
5.2.4 Automatic ignition where multiple main burners are fitted
5.2.5 Burner control
5.2.6 Flame safeguards
5.3 AIR-GAS MIXING MACHINES AND MIXING BLOWERS
5.3.1 General
5.3.2 Materials
5.3.3 Strength of pipe and fittings
5.3.4 Safety shut off system to be fitted
5.3.5 Safety shut off system to cause lockout
5.3.6 Air-gas ratio
5.3.6.1 Locking provision for air-gas ratio from a mixing machine
5.3.6.2 Limiting provision for air-gas ratio from a mixing machine
5.3.6.3 Air-gas ratio from a mixing blower
5.3.7 Mixing blower outlets
5.3.8 Flashback requirements for air-gas mixing machines
5.3.9 Rupture of blow-out disc
5.3.10 Flame arrestor between air-gas mixing machine and burner
5.3.11 Flame arrestor at mixing machine
5.3.12 Flame arrestors
5.3.13 Air-gas mixing machines - requirement for non-return valve
5.4 SPECIAL ATMOSPHERES AND ATMOSPHERE GENERATORS
5.4.1 General
5.4.2 Piping for special atmospheres
5.4.3 Storage of special atmosphere
5.4.4 Storage container for compressed special atmosphere
5.4.5 Venting and disposal of special atmospheres
5.4.6 Discharge using a vent line
5.4.7 Start-up of an atmosphere generator
5.4.8 Ignition
5.4.9 Requirement where the air-gas ratio is variable
5.4.10 Requirements where the air-gas ratio is fixed
5.4.11 Automatic relief device
5.4.12 Flame arrestor
5.4.13 Water-cooled equipment
5.4.14 Exothermic atmosphere generators
5.4.14.1 Flame safeguard requirement
5.4.14.2 Flame safeguard bypass
5.4.14.3 Pressure detectors to be fitted
5.4.14.4 Pressure detectors to be interlocked
5.4.14.5 Interlocking combustible atmosphere flow
5.4.14.6 Purging
5.4.14.7 Air-gas ratio control
5.4.15 Endothermic atmosphere generators
5.4.15.1 Safety shut off valves to be fitted
5.4.15.2 Air shut off device
5.4.15.3 Pressure detectors
5.5 PROCESS AFTER-BURNERS
5.5.1 General
5.5.2 Control of process products
5.5.2.1 Requirement for interlocks
5.5.2.2 Process products-percentage of LEL
5.5.3 Combustion air supply
5.5.4 Shutting down of process afterburner
5.5.5 Pre-purge
5.6 STEAM AND HOT WATER BOILERS
5.7 DIRECT-FIRED AIR HEATERS AND CURTAINS
5.7.1 General
5.7.2 Heater air supply
5.7.3 Air flow sensing device
5.7.4 Pre-purge
5.7.5 Temperature limit device
5.7.6 Start gas rate
5.7.7 Combustion
5.7.7.1 Limits for combustion products
5.7.7.2 Samples of heated air to be taken
5.7.7.3 Limitation on air temperature
5.7.7.4 Combustion at minimum air flow
5.7.8 Markings
5.7.8.1 Marking plate to be fitted
5.7.8.2 Restriction on installation
5.8 STATIONARY GAS ENGINES AND TURBINES
5.8.1 General
5.8.2 Requirement for safety shut off valve system
5.8.2.1 Safety shut off system to be fitted
5.8.2.2 Safety shut off valves and vent valves
5.8.2.3 Emergency isolation and vent valves
5.8.2.4 Activation of the safety shut off system to shut off gas supply
5.8.3 Turbine purging
5.8.4 Gas supply flexible connection
5.8.5 Exhaust system to be fitted
5.8.6 Flexible connection to be fitted to exhaust line
5.8.7 Requirements of an exhaust system
5.8.8 Exhaust terminal location
5.8.9 Ventilation
5.8.10 Requirements for Ignition
5.8.11 Extinction safety time
5.8.12 Indirect flame monitoring
5.9 INCINERATORS AND CREMATORS
5.9.1 General
5.9.2 Primary burner interlock
5.9.3 Combustion air
5.9.4 Pre-purge
5.9.5 Flues
5.9.5.1 Flues not to be interconnected
5.9.5.2 Limiting updraught
5.10 ROTARY PROCESS EQUIPMENT AND OVENS-DIRECT-FIRED
5.10.1 General
5.10.2 Purging
5.10.3 Provision of air
5.10.4 Explosion relief
5.10.5 Temperature limit device
5.10.6 Access for cleaning
5.10.7 Processes with solvents or combustible dust
5.10.7.1 Provision of dilution air
5.10.7.2 Recirculation air fans
5.10.7.3 Monitoring of solvent LEL
5.11 SMOKE OVENS-DIRECT-FIRED
5.11.1 Lighting torch
5.11.2 Combustion air
5.11.2.1 Combustion air to be provided from outside of oven
5.11.2.2 Restrictions on the use of ducting
5.11.2.3 Smoke not to interfere with combustion
5.11.3 Explosion relief requirements
5.11.4 Loading doors
5.11.5 Sawdust trays
5.11.6 Flue
5.11.6.1 Minimum requirements for natural draught flue
5.11.6.2 Flue damper
5.12 WATER HEATERS
5.12.1 General
5.12.2 Thermostat
5.12.3 Over-temperature control
5.12.3.1 Over-temperature cut-out device to be fitted
5.12.3.2 Over-temperature cut-out to initiate lockout
5.12.4 Unvented water heaters
5.12.4.1 Relief valve to be fitted
5.12.4.2 Location of relief valves
5.12.4.3 Heaters containing 1L of water or less
5.12.5 Provision for draining
5.13 MULTI-FUEL FIRING SYSTEMS
5.13.1 Alternative multi-fuel systems
5.13.1.1 Isolation of alternative fuel supply
5.13.1.2 Alternative fuel system to be interlocked
5.13.1.3 Fuel lines to be sealed on disconnection
5.13.2 Multi-fuel simultaneous firing systems
5.13.2.1 Maximum operating input
5.13.2.2 Combustion air requirement
APPENDIX A - TYPICAL INFORMATION AND TECHNICAL DATA
APPENDIX B - TYPICAL PROCEDURE FOR THE APPROVAL OF INDUSTRIAL AND COMMERCIAL APPLIANCES
APPENDIX C - TYPICAL VALVE TRAIN ARRANGEMENTS
APPENDIX D - FLAME SAFEGUARD SELECTION
APPENDIX E - PRO-FORMA LETTER TO THE GAS TECHNICAL REGULATOR FROM A CONTRACTOR/COMPANY CE...
APPENDIX F - GAS/AIR RATIO CONTROL PROGRAMMABLE ELECTRONIC SYSTEMS
F1 INTRODUCTION
F2 DEFINITION OF GAS/AIR RATIO CONTROL PROGRAMMABLE ELECTRONIC SYSTEMS
F3 PARAMETERISABLE SYSTEMS THAT DO NOT REQUIRE A LOW OXYGEN LIMIT DEVICE
F4 PARAMETERISABLE SYSTEMS THAT REQUIRE A LOW OXYGEN LIMIT
F5 PES GAS/AIR RATIO CONTROL SYSTEMS
F6 ADDITIONAL REQUIREMENTS FOR BURNER MANAGEMENT SYSTEMS FITTED WITH LOW OXYGEN LIMIT DEV...
F6.1 The oxygen probe that could act as an ignition source
F6.2 With an oxygen probe that does not act as an ignition source
APPENDIX G - MAINTENANCE AND CHECKS OF SAFETY DEVICES
G1 INTRODUCTION
G2 REGULAR TESTING
G3 PERSONNEL AND ORGANIZATION
G4 GENERAL OUTLINE OF PROCEDURES
G5 TESTING SCHEDULES
APPENDIX H - TYPICAL OPERATING SEQUENCE FOR AN AUTOMATIC FORCED OR INDUCED DRAUGHT BURNER...
APPENDIX I - TYPICAL COMMISSIONING PROCEDURE
I1 SCOPE
I2 STAGE 1 PRELIMINARY INSPECTION
I3 STAGE 2 ACTIVATION-RUN WITHOUT FUEL
I4 STAGE 3 ACTIVATION-RUN WITH FUEL
I5 STAGE 4 OPERATION
I6 STAGE 5 COMPLETION
APPENDIX J - TYPICAL FIELD CHECK LIST
  
File Format:  PDF(Acrobat Reader) or Word version doc Document
File Size:  691KB
Tile in English:  industrial and commercial gas-fired appliances

Full Text Information

Related

Top 10

New 10

PC Version