jQuery Mobile Framework
Search Home >> Standards Wordwide >> Other Standards >> ADM 1-2010 Aluminum Design Manual

ADM 1-2010 Aluminum Design Manual

Standard Number:  ADM 1-2010
Title:  Aluminum Design Manual
Language:  English
Replaced by Standard:  ADM 1:2015

Replacing Standard:  ADM 1:2005

Status:  Current
Publisher:  Other Standards
Price:  
Number of Pages:  

Description:Specifies rules for determining the strength of aluminum structural components and minimum strengths for wrought, cast, and welded aluminum alloys and aluminum fasteners.  
Catalog:PART I-A
Section 1 General
Section 2 Design Procedure
Section 3 General Design Rules
Section 4 Special Design Rules
Section 5 Mechanical Connections
Section 6 Fabrication
Section 7 Welded Construction
Section 8 Testing
PART I-B
Section 1 General
Section 2 Design Procedure
Section 3 General Design Rules
Section 4 Special Design Rules
Section 5 Mechanical Connections
Section 6 Fabrication
Section 7 Welded Construction
Section 8 Testing
PART II-A
Section 1 General
Section 2 Design Procedure
Section 3 General Design Rules
Section 4 Special Design Rules
Section 5 Mechanical Connections
Section 6 Fabrication
Section 7 Welded Construction
Section 8 Testing
REFERENCES
PART III
1.0 Introduction
2.0 Design of Aluminium Structures
3.0 Member and Component Behaviour
4.0 Fatigue
5.0 Joints and Joining
6.0 Sandwich Panels and Beams
7.0 Extrusion Design
8.0 Prevention of Corrosion
9.0 Fire Protection
10.0 References
PART IV
1.0 Features of Aluminum-General
2.0 Features of Aluminum/Metallurgical Aspects
3.0 Designation System for Wrought Aluminum and
Aluminum Alloys
4.0 Cast Aluminum and Aluminum Alloy Designation
System
5.0 Effect of Alloying Elements
6.0 Temper Designation System
Table 1 Comparative Characteristics and Applications
Table 2 Foreign Alloy Designations and Similar
AA Alloys
PART V
1.0 Introduction
2.0 References
Tables
1 Minimum Mechanical Properties for Aluminum
Alloys
2 Minimum Mechanical Properties for Welded
Aluminum Alloys
3 Mechanical Property Limits for Aluminum
Sand Casting and Permanent Mold Casting
Alloys
4 Minimum Mechanical Properties of Threaded
Fastener Alloys
5 Typical Mechanical Properties
6 Typical Physical Properties-Thermal and
Electrical
7 Typical Physical Properties-Density
8 Typical Tensile Properties at Various
Temperatures
PART VI
Tables
1 Nomenclature
2 Section Designations
3 Weights pe Square Foot
4 Developed Length of Material for 90-Degree
Bends-Inches
5 Aluminum Association Standard Channels
6 Channels
7 Channels - Army-Navy
8 Special Channels
9 Channels - American Standard
10 Wing Channels
11 Aluminum Association Standard I-Beams
12 Wide Flange Sections - H-Beams
13 Wide Flange Sections - Army-Navy Series
14 I-Beams - American Standard
15 I-Beams
16 Angles - Equal Legs
17 Square End Angles - Equal Legs
18 Angles - Unequal Legs
19 Square End Angles - Unequal Legs
20 Bulb Angles
21 Bulb Angles, Army-Navy Series
22 Army-Navy and Special Tee Sections
23 Tee Sections
24 Zee Sections
25 Round Tube
26 Pipe
27 Square Tube
28 Rectangular Tube
29 Geometric Shapes
30 Decimal Equivalents, Squares, Circle Areas,
and Circumferences, Fillet Areas, and Data
for Determining Fillet Perimeters for Small
Radii
31 Designed Dimensions and Weights-Commercial
Roof and Siding
32 Nominal Section Properties-Commercial
Roofing and Siding
33 Decimal Equivalents in Inches of Sheet Metal
and Wire Gages
PART VII
Introduction
Compressive Strength Curves
Allowable Stress Tables for Building and Similar
Type Structures
Allowable Stress Tables for Bridge and Similar
Type Structures
Allowable Load Tables
Fasteners
Bend Radii
Beam Formulas
PART VIII
1 Rod, round
2 Strap, rectangular
3 I-Beam
4 Tube, square
5 Tube, round
6 Plate
7 Rivets
8 Pin
9 I-Beam
10 Box section latticed
11 Wide flange section
12 Tube, square
13 Tube, square, with stiffeners
14 Tube, round
15 I-Beam
16 Girder, welded
17 Welded girder, transverse stiffeners
18 Tube, round
19 Bar, rectangular
20 Tube, rectangular
21 I-Beam
22 Unsymmetric shape
23 Channel
24 Welded beam
25 Welded beam, stiffened web
26 I-Beam
27 Girder, reiveted, stiffened web
28 Curtainwall I-Beam
29 Formed sheet
30 Self-tapping screw
APPENDIX 1
INDEX  
File Format:  PDF(Acrobat Reader) or Word version doc Document
File Size:  343KB
Tile in English:  Aluminum Design Manual

Full Text Information

Related

Top 10

New 10

PC Version